Sure Seal EZY AS 1-2-3 Water Based Sealer

Sure Seal Ezy-As 1.2.3. is a unique, penetrating sealer that allows you to create the level of finish you require from a low sheen, semi-gloss, or full gloss by application of 1, 2, or 3 coats…the choice is yours! Sure Seal® Ezy-As 1.2.3. is a revolutionary water based formula that is non-flammable and environmentally friendly. It provides a tough and durable finish on porous surfaces and protects against oil and water-based stains.

KEY FEATURES

This easy-to-use, low odour product will not peel, flake off the surface and resists abrasion. It can be used on both interior and exterior surfaces such as pavers, slate, terrazzo, terracotta, sandstone, limestone, concrete and brick.

BENEFITS & CHARACTERISTICS:

• Create your own finish by the number of coats applied
• Provides a level of gloss from low to high
• Water-based formulation
• Non-flammable & non hazardous
• Environmentally friendly with no VOC’s
• Resists UV light degradation
• No blooming or pooling on the surface
• Protects against water and oil-based stains

APPLICATION INSTRUCTIONS:

Use as is. Do not dilute. Always test product in an inconspicuous area first to determine suitability for the intended use. If inside, make sure the area is well ventilated. Ensure that the surface and underlying substrate is completely dry, clean and free from any debris. Existing stains must be removed prior to sealant application. Protect any adjacent surfaces to the application area to avoid any overspray. If overspray occurs, wipe off with damp cloth immediately. On newly-laid floors, it is recommended that 24-36 hours lapse before application of the sealer. On smooth surfaces apply by brush or lambs-wool applicator. On rough surfaces apply by brush or roller. Make sure the area is well covered. For best results apply in light even coats. If application is to a vertical surface, a build-up may occur at the bottom of the substrate. If this occurs, dry brush over the area before it dries. Drying time is anywhere from 1-2 hours depending on weather conditions. Because of the varying porosity of surfaces, more coats may be required so repeat the procedure until the desired level of sheen is achieved. Do not apply to damp surfaces and substrates or surfaces and substrates at or below 8°C. Allow to cure for 24 hours during which time the treated area should be kept dry and free from soils. Light foot traffic is possible approximately 4 hours after the area has dried. After sealing driveways, do not drive vehicles on the surface for 48 hours. NOTE: NOT RECOMMENDED for application on horizontal surfaces in wet areas such as bathroom floors or pool surrounds, as product may become slippery when wet. This product is not suitable for application on polished/unpolished marble, granite, porcelain or other dense surfaces.

COVERAGE & PACKAGING

Available in:

• 1 Litre ( also available in carton 12x1L)
• 4 Litre ( also available in carton 4x4L)
• 20 Litre Drum

Coverage:

One litre will cover up to approx. 22 square metres depending on the porosity or type of surface being treated, the number of coats being applied, and the method of application.

MAINTENANCE

Clean exterior areas using a garden hose with a pressure nozzle. Clean interior areas by mopping or wiping with a soft cloth or sponge. If oil spills are present, clean the area using a mild detergent and water. Do not use harsh cleaning agents such as abrasive powders, ammonia, acids, bleach, solvents or abrasive scrubbing pads.

Cleanup: Rinse application equipment in water.

TECHNICAL DATA:

Appearance: White milky liquid

Volatiles: Not applicable

Transport: Not regulated

DG Class: Non dangerous goods

Hazchem: Non hazardous

 Contact us for information on bulk purchases. Request for quote! Order now from Sydney Industrial Coatings for free shipping insurance, trade prices, and fast nationwide delivery.

Download Technical Datasheet.